10 Technical guidelines

This section contains some technical guidelines for the Optimizer API for C users.

For modelling guidelines check one of the following sections:

  • Section 13 for how to address numerical issues in modelling and how to tune the continuous optimizers.
  • Section 14 for how to tune the mixed-integer optimizer.

10.1 Memory management and garbage collection

Users who experience memory leaks, especially:

  • memory usage not decreasing after the solver terminates,
  • memory usage increasing when solving a sequence of problems,

should make sure that the memory used by the task is released when the task is no longer needed. This is done with the method MSK_deletetask. The same applies to the environment when it is no longer needed.

  MSK_deletetask(&task);
  MSK_deleteenv(&env);

10.2 Multithreading

Thread safety

Sharing a task between threads is safe, as long as it is not accessed from more than one thread at a time. Multiple tasks can be created and used in parallel without any problems.

Parallelization

The interior-point and mixed-integer optimizers in MOSEK are parallelized. By default MOSEK will automatically select the number of threads. However, the maximum number of threads allowed can be changed by setting the parameter MSK_IPAR_NUM_THREADS and related parameters. This should never exceed the number of cores. See Sections 13 and 14 for more details for the two optimizer types.

The speed-up obtained when using multiple threads is highly problem and hardware dependent. We recommend experimenting with various thread numbers to determine the optimal settings. For small problems using multiple threads may be counter-productive because of the associated overhead.

By default the optimizer is run-to-run deterministic, which means that it will return the same answer each time it is run on the same machine with the same input, the same parameter settings (including number of threads) and no time limits.

10.3 Efficiency

Although MOSEK is implemented to handle memory efficiently, the user may have valuable knowledge about a problem, which could be used to improve the performance of MOSEK This section discusses some tricks and general advice that hopefully make MOSEK process your problem faster.

Reduce the number of function calls and avoid input loops

For example, instead of setting the entries in the linear constraint matrix one by one (MSK_putaij) define them all at once (MSK_putaijlist) or in convenient large chunks (MSK_putacollist etc.)

Use one environment only

If possible share the environment between several tasks. For most applications you need to create only a single environment.

Read part of the solution

When fetching the solution, data has to be copied from the optimizer to the user’s data structures. Instead of fetching the whole solution, consider fetching only the interesting part (see for example MSK_getxxslice and similar).

Avoiding memory fragmentation

MOSEK stores the optimization problem in internal data structures in the memory. Initially MOSEK will allocate structures of a certain size, and as more items are added to the problem the structures are reallocated. For large problems the same structures may be reallocated many times causing memory fragmentation. One way to avoid this is to give MOSEK an estimated size of your problem using the functions:

None of these functions changes the problem, they only serve as hints. If the problem ends up growing larger, the estimates are automatically increased.

Do not mix put- and get- functions

MOSEK will queue put- requests internally until a get- function is called. If put- and get- calls are interleaved, the queue will have to be flushed more frequently, decreasing efficiency.

In general get- commands should not be called often (or at all) during problem setup.

Use the LIFO principle

When removing constraints and variables, try to use a LIFO (Last In First Out) approach. MOSEK can more efficiently remove constraints and variables with a high index than a small index.

An alternative to removing a constraint or a variable is to fix it at 0, and set all relevant coefficients to 0. Generally this will not have any impact on the optimization speed.

Add more constraints and variables than you need (now)

The cost of adding one constraint or one variable is about the same as adding many of them. Therefore, it may be worthwhile to add many variables instead of one. Initially fix the unused variable at zero, and then later unfix them as needed. Similarly, you can add multiple free constraints and then use them as needed.

Do not remove basic variables

When performing re-optimizations, instead of removing a basic variable it may be more efficient to fix the variable at zero and then remove it when the problem is re-optimized and it has left the basis. This makes it easier for MOSEK to restart the simplex optimizer.

10.4 The license system

MOSEK is a commercial product that always needs a valid license to work. MOSEK uses a third party license manager to implement license checking. The number of license tokens provided determines the number of optimizations that can be run simultaneously.

By default a license token remains checked out from the first optimization until the end of the MOSEK session, i.e.

  • a license token is checked out when MSK_optimize is first called, and
  • it is returned when the MOSEK environment is deleted.

Calling MSK_optimize from different threads using the same MOSEK environment only consumes one license token.

Starting the optimization when no license tokens are available will result in an error.

Default behaviour of the license system can be changed in several ways:

  • Setting the parameter MSK_IPAR_CACHE_LICENSE to MSK_OFF will force MOSEK to return the license token immediately after the optimization completed.
  • Setting the license wait flag with the parameter MSK_IPAR_LICENSE_WAIT will force MOSEK to wait until a license token becomes available instead of returning with an error. The wait time between checks can be set with MSK_putlicensewait.
  • Additional license checkouts and checkins can be performed with the functions MSK_checkinlicense and MSK_checkoutlicense.
  • Usually the license system is stopped automatically when the MOSEK library is unloaded. However, when the user explicitly unloads the library (using e.g. FreeLibrary), the license system must be stopped before the library is unloaded. This can be done by calling the function MSK_licensecleanup as the last function call to MOSEK.

10.5 Deployment

When redistributing a C application using the MOSEK Optimizer API for C 8.1.0.24, the following libraries must be included:

64-bit Linux 64-bit Windows 32-bit Windows 64-bit Mac OS
libmosek64.so.8.1 mosek64_8_1.dll mosek8_1.dll libmosek64.8.1.dylib
libiomp5.so libomp5md.dll libomp5md.dll  
libcilkrts.so.5 cilkrts20.dll cilkrts20.dll libcilkrts.5.dylib